It is generally accepted that one of the most optimal fences in terms of price / quality ratio is a fence from the chain-link mesh .
Advantages of this fence:
The fence is transparent, which allows air to circulate freely from the neighboring area to yours and back, the area will not be stuffy, as is the case when they are fenced on all sides with a windproof fence. Transparent fence does not obscure the site.
The fence is relatively cheap.
The mesh fence is beautiful and easy to install.
If you purchase a galvanized mesh fence, you will not take care of it for 20-25 years. The galvanized mesh fence does not rust, so it does not need to be tinted
The height of the Fence varies from 1m to 4m.
In order for the fence not to sag over time, it is necessary to purchase a chain-link mesh made of wire 2.2 mm and higher, install reinforcing galvanized wire on the top and bottom, which you pass between the upper and lower cells.
If you want your chain-link fence to be not only beautiful, but also to perform a security function, then you need to stretch barbed wire, flat fidget or bulk fiddle over the fence.
If you weave a plastic plank or artificial needles into a chain-link mesh spiral, you can get an unusual opaque exclusive fence.
Our company is ready to supply you with both the entire range of chain-link mesh and posts for mounting a fence .
Cheaper than a chain-link there is only a fence made of mesh TM Cossack lightweight .
Installation of a fence from a chain-link grid
The chain-link fence is a fairly common fence. We will help with the choice of which mesh to buy and how to install the fence.
Materials and tools for installing a fence
|
|
Preparing to Install a Fence
one
Define the boundaries of your site. It is recommended that all posts be installed approximately 10 cm inside the site so that the post foundation does not extend into adjacent areas.
2
Measure the length of your planned fence to determine how many meters of chain-link mesh and cross bars you will need.
3
Mark the location of each support post (corner, end and gate posts are called support posts) with pegs. When determining the location of gate posts, remember that clearance is needed for hinges, latches, etc. Therefore, if you are making a gate with an opening of 6 m, the distance between the supports should be 6 m plus the clearance for fasteners.
Installation of support poles
one
Dig holes 20 cm in diameter and 60-80 cm deep, with gentle sides. The exact diameter and depth will depend on local weather and soil conditions.
2
Use a pencil or chalk to mark the ground line on the posts. The height of the support posts above ground level will be equal to the height of the chain-link grid plus 5 cm.
3
Place a support post in the center of the hole. Make sure it is level and at the right height (the pencil mark should be at ground level). Fill the surrounding area with concrete. Level the surface and slope the foundation to the outside to drain water.
Installation of intermediate posts
one
When the foundation of the support pillars has hardened, stretch the guide thread tightly between them. The thread should be located on the outside of the posts 10 cm below the top of the post.
2
Dig holes for intermediate posts 15 cm wide and 45-50 cm deep, with sloping sides. Place a post in the center of the hole. Make sure it is level with the support posts and at the correct height. Fill the surrounding area with concrete. Level the surface and slope the foundation to the outside to drain water.
Mounting installation
You can use both factory-made fasteners and homeenmade ones. Their difference will consist in the difference of coatings. Factory fasteners are usually coated with zinc and / or polymer, which protects them from rust. Homemade fasteners are usually welded to the support, and crossbars or a mesh are already attached to them, forming a tension. Factory fasteners, tightened with a bolt.
Cover all supports with plugs that prevent water from entering inside.
Stretching the fence
Pass reinforcement through the extreme mesh cells to maintain uniform tension throughout the web. After that, attach the reinforcement to the mounts on the supports.
It is necessary to fix the grid on the intermediate supports with the help of clamps.
For better tension, it is better to pass the tension wire through the lower mesh cells. The ends are attached to the support poles, and the wire itself is tied with clamps or clamps to the intermediate supports.
How to split a mesh netting
In order to divide the chain-link, it is necessary to open the ends of the spirals in the place where it is necessary to divide the canvas and unscrew the spiral. Then the unscrewed spiral can be screwed back into one of the two canvases.
When installing a mesh fence, in this way the Chain-link will not sag for a long time and the fence will serve you faithfully.